Description
Talley took the guesswork out of mounting glass on your Browning X-Bolt with this one-piece ring and base design. Instead of a separate base and ring that can shift or fall out of alignment, each unit is machined as a single rigid piece that bolts right to the receiver. That means there's no interface to work loose and no joint to throw off your alignment, which is exactly what you want when you're trusting your setup at longer ranges.
These are the High height, 34mm versions in a burnt bronze finish, made to pair nicely with the Hells Canyon and other X-Bolt rifles wearing similar coatings. The 34mm ring diameter fits the larger main tubes found on a lot of today's long-range optics, so you've got plenty of room for a serious scope. The Short/Super Short profile is cut to match the correct action length on your X-Bolt.
What the 20 MOA Cant Does for Your X-Bolt
The built-in 20 minutes of angle is the real story here. That forward lean gives you a big chunk of extra elevation travel in your scope before you run out of adjustment, so you can dial for drop way downrange without maxing out your turret. If you're shooting past where your rifle and load start dropping hard, this is the kind of detail that keeps you on target.
Machined and Finished for the Long Haul
Talley runs these mounts through full CNC machining from high-grade aircraft aluminum, hitting tight tolerances that let them skip the lapping step entirely. They come ready to install right out of the box. The burnt bronze finish looks clean and holds up to the kind of wear a hunting rifle sees in the field.
Built in America for the Browning X-Bolt
These are made in the USA and designed specifically around the X-Bolt footprint, so you get a precise fit without fighting your hardware. The one-piece alloy design delivers the rigidity people expect from steel while keeping overall weight down, which your shoulder will appreciate after a long day of carrying.
Key Specifications
- Manufacturer: Talley
- Manufacturer Part Number: HC850735SM
- UPC: 810301025066
- Fits: Browning X-Bolt (Short/Super Short Action)
- Tube Diameter: 34mm
- Ring Height: High
- Built-In Cant: 20 MOA
- Design: One-Piece Integrated Ring and Base
- Material: High-Grade Aircraft Aluminum
- Construction: Fully CNC Machined
- Finish: Burnt Bronze
- Mounting Hardware: 6-48 Screws
- Lapping Required: No
- Sold As: Pair (Front and Rear)
- Country of Origin: Made in USA
What’s Included
- One set of Talley one-piece scope mounts (front and rear)
- 6-48 mounting screws
- T-15 Torx wrench
Frequently Asked Questions
Will these Talley mounts fit my Browning X-Bolt?
Yes, these are designed specifically for the Browning X-Bolt in the Short/Super Short action length. The one-piece design is machined to match the X-Bolt receiver footprint, so you get a precise fit without extra fitting or filing. Just double-check your rifle is a short or super short action rather than a long or magnum action before ordering.
What does the 20 MOA cant actually do?
The 20 MOA built into the mount tilts your scope slightly forward, which gives you extra elevation adjustment in your turret for reaching out to distance. This lets you dial in more bullet drop before running out of travel, so it's a real benefit for long-range work. For shorter-range hunting at normal distances, a standard 0 MOA mount would also work fine.
Do I need to lap these rings before installing a scope?
No. Talley CNC machines these to tight tolerances so they're ready to go right out of the box, and lapping is not required. In fact, Talley notes that lapping can void their product support, so you can skip that step entirely.
Will a 34mm scope fit in these rings?
These rings are made for 34mm main tube scopes, which is the larger diameter found on many long-range and higher-end optics. Make sure the main tube on your scope measures 34mm and not 30mm or 1 inch before mounting. A T-15 wrench is included to tighten the ring caps and bases.




Reviews
There are no reviews yet.