Description
Small-bore rifles like the .17 HMR, .204 Ruger, and .17 Hornet leave very little room for error when you're cleaning them, and a flimsy rod that flexes inside the bore is how scratches and worn rifling happen. The Montana X-Treme .17 to .20 caliber rod solves that with a single-piece spring steel shaft measuring 30 inches, sized to reach through most varmint and rimfire barrels while staying stiff enough to power through stubborn fouling.
What Sets the Montana X-Treme .17-.20 Rod Apart
This rod is made from high-strength spring steel and finished with a proprietary non-embedding coating. That coating matters more than it sounds. On cheaper rods, grit and abrasive residue get pressed into the surface and turn the rod itself into a piece of sandpaper dragging against your rifling. The Montana X-Treme coating resists that embedding, so the shaft stays smooth and your bore stays protected wash after wash.
Bearings and Handle Built for Real Cleaning Sessions
The rod carries two sets of thrust bearings held between hardened stainless steel retainers. During the push and pull stroke, those bearings spread the load evenly and let the rod spin freely so your jag or brush follows the rifling instead of fighting it. A nice side benefit is that the bearings keep your jag or brush from backing off and unscrewing mid-stroke, which is a headache every rifle owner has dealt with at least once.
Getting the Most From the .17-.20 Caliber Rod
The handle is machined aluminum and kept slim on purpose so it clears the stock when you clean from the breech, the right way to do it on most bolt guns. The threaded tip uses a 5 x 40 pattern, which is the standard for small-bore accessories, so it pairs up with common jags, brushes, and patch loops in that size range. Take care of it, wipe it down after use, and this is the kind of rod that outlasts a stack of the disposable ones.
Key Specifications
- Manufacturer: Montana X-Treme
- Manufacturer Part Number: 9130
- UPC: 658638291309
- Caliber Range: .17 (.172) to .20 (.204)
- Length: 30 inches
- Thread Size: 5 x 40 female
- Rod Material: High-strength spring steel
- Coating: Proprietary non-embedding
- Construction: One-piece
- Handle: Machined aluminum with dual thrust bearings
- Style: Rifle
- Country of Origin: USA
What’s Included
- Montana X-Treme .17 to .20 caliber 30-inch cleaning rod with machined aluminum handle
Frequently Asked Questions
What calibers does the Montana X-Treme 30-inch rod fit?
It's built for .17 through .20 caliber bores, covering popular rounds like the .17 HMR, .17 Hornet, and .204 Ruger. The slim shaft is sized to slide through those tight barrels without contacting the rifling. If you shoot .22 caliber or larger, you'll want to step up to the next size Montana X-Treme rod.
What thread size does this rod use for jags and brushes?
The tip is threaded 5 x 40, which is the standard pattern for small-bore cleaning accessories. That means it works with common .17 to .20 caliber jags, bore brushes, and patch loops in that thread size. You won't be hunting for oddball adapters to get it set up.
Why does the non-embedding coating on the Montana X-Treme rod matter?
Abrasive fouling and grit can press into the surface of an uncoated or cheaply coated rod, essentially turning the rod into a fine abrasive that wears your bore over time. The proprietary coating on this rod resists that embedding so the shaft stays smooth. That protects your rifling through years of regular cleaning.
What do the thrust bearings actually do?
The two sets of thrust bearings let the rod rotate freely as you push and pull, so the jag or brush can follow the twist of the rifling instead of dragging against it. They also help keep your jag or brush from unscrewing partway through a stroke. It makes for a smoother, more controlled cleaning session.





Reviews
There are no reviews yet.