Description
If you're loading .40 S&W or 10mm Auto and chasing better feeding out of your semi-auto, a dedicated taper crimp die earns its spot on the press. This Hornady die is built specifically for the .400 diameter cases those two calibers share, and it does one job extremely well: it presses the case walls back into a straight, parallel shape after seating. That matters because straight-wall auto pistol cases headspace on the case mouth ledge, so you need that mouth deflared without rolling it into the bullet like you would with a revolver cartridge.
What the Hornady Taper Crimp Die Actually Does
During bullet seating you flare the case mouth a little so the bullet starts clean. This die removes that flare and squeezes the case walls tight against the bullet shank while keeping a sharp, square edge intact for proper headspacing. The result is a round that drops into the chamber and cycles reliably. Keep in mind that on auto pistol rounds the taper crimp is there to aid feeding, not to lock the bullet in place. Case neck tension from your sizing die does the holding, so you don't want to overdo it.
Fit With Your Hornady Reloading Setup
This works as a standalone crimping step or as an add-on to a Hornady Custom Grade New Dimension 3-die pistol set. A lot of reloaders run it as a separate final station because seating and crimping in two operations gives cleaner, more consistent results than trying to do both at once. It's compatible with standard 7/8-14 threaded presses, so it drops right into whatever single-stage or progressive setup you're already running.
Built to Last
Hornady machines these from high-quality steel and polishes the interiors, which keeps crimps uniform load after load and holds up over years of use. For the best, most repeatable crimp, trim your brass to a consistent case length first. Uniform case length is the biggest factor in getting an even crimp on every round. A shellholder is not included and is selected to match your press and caliber.
Key Specifications
- Manufacturer: Hornady
- Manufacturer Part Number: 044171
- UPC: 090255441710
- Caliber: .40 S&W / 10mm Auto (.400)
- Die Type: Taper Crimp Die
- Series: Custom Grade New Dimension / Series II
- Material: High-quality steel, polished interior
- Gun Type: Pistol / Semi-Automatic
- Thread: 7/8-14 standard press
- Quantity: 1 die
- Shipping Weight: 0.375 lb
What’s Included
- 1 Hornady Taper Crimp Die (.40 S&W / 10mm Auto)
- Hornady lock ring
Frequently Asked Questions
Do I need a taper crimp die for .40 S&W and 10mm?
For semi-auto pistol cartridges like .40 S&W and 10mm, a taper crimp is the way to go. These rounds headspace on the case mouth, so you want the flare removed without rolling the edge into the bullet. This Hornady die does exactly that and helps your reloads feed and chamber reliably.
Does the Hornady Taper Crimp Die hold the bullet in place?
Not really, and that's by design. On auto pistol rounds, neck tension from your sizing step is what grips the bullet. The taper crimp's real job is deflaring the case mouth and streamlining the round so it feeds smoothly, not clamping down on the bullet.
Will this die work with my Hornady 3-die pistol set?
Yes. It's a natural addition to a Hornady Custom Grade New Dimension 3-die pistol set and fits any standard 7/8-14 threaded press. Many reloaders run it as a dedicated final station so seating and crimping happen in separate steps for a cleaner result.
Is a shellholder included with the Hornady Taper Crimp Die?
No, the shellholder is sold separately. You'll want one matched to your press and to the .40 S&W / 10mm case head. For the most consistent crimp, trim your brass to a uniform length before running it through the die.




Reviews
There are no reviews yet.