Description
If you've ever pulled a scope off a rifle and found ugly ring marks ground into the tube, you'll appreciate what Burris did with the Signature line. These medium-height 1-inch rings are machined from solid steel and finished in matte black, and the real trick is the Pos-Align insert system. Instead of steel clamping straight onto your scope, a pair of synthetic inserts sits between the ring and the tube, spreading contact across nearly the whole surface. The result is a serious grip that holds zero without crushing or scratching your optic.
What the Pos-Align Inserts Do for Your Setup
The inserts aren't just padding. They pivot inside the ring housings, which lets you take out small alignment problems between the front and rear rings. That means less stress on your scope tube and a cleaner, more repeatable zero. The synthetic material is slightly softer than a hard-anodized scope body, so it grips firmly while leaving the finish alone. This pair ships with one set of concentric inserts ready to go.
Fitting the Burris Signature Rings to Your Rifle
This set is built for the rimfire and airgun crowd. The rings clamp to 3/8-inch and 11mm grooved dovetail receivers, which covers most .22 rifles and a big chunk of air rifles out there. Burris includes a spare set of clamps specifically cut for 11mm dovetails, and those are stamped with the letter A so you know which ones to grab. Medium height puts the center of a 1-inch tube at about .90 inches, which leaves room for most standard objective bells without riding too high.
Burris has been making the Signature rings for a long time, and they've earned a reputation for holding up in any weather and any kind of shooting. They carry the Burris Forever Warranty, so if something ever goes wrong, you're covered. For a dependable, scope-friendly mount on a plinker, hunting rimfire, or air rifle, these are a proven pick.
Key Specifications
- Manufacturer: Burris
- Model: Signature
- Manufacturer Part Number: 420554
- UPC: 000381205544
- Ring Style: Rimfire / Airgun
- Tube Diameter: 1 inch
- Ring Height: Medium
- Height to Center: .90 in.
- Construction: Solid steel
- Finish: Matte Black
- Fits: 3/8" and 11mm grooved dovetail receivers
- Top Ring Torque: 20 inch-lbs
- Ring Cross Bolt Torque: 40 inch-lbs
- Warranty: Burris Forever Warranty
What’s Included
- Pair of 1" medium Signature rings (matte black)
- One set of concentric Pos-Align inserts
- Spare set of clamps for 11mm dovetails (stamped with letter A)
Frequently Asked Questions
What receivers do the Burris Signature rimfire rings fit?
These rings are made for 3/8-inch and 11mm grooved dovetail receivers, which covers most .22 rimfire rifles and many air rifles. Burris includes a spare set of clamps cut specifically for 11mm dovetails, and those clamps are stamped with the letter A so they're easy to identify. If your receiver is a standard narrow 3/8-inch dovetail, use the primary clamps that come installed.
Will the Pos-Align inserts scratch or mark my scope tube?
No. The synthetic inserts are made from a material slightly softer than a hard-anodized scope body, so they grip firmly without crushing or scratching the finish. Because the inserts spread contact across nearly the whole tube surface, you avoid the ring marks that conventional steel rings can leave behind.
What does medium ring height give me on these Signature rings?
Medium height places the center of a 1-inch tube at about .90 inches above the base. That clearance works well for most standard objective bells found on rimfire and airgun scopes. If your scope has a larger objective, you may want to step up to the high version instead.
Do these rings help with scope alignment?
Yes. The Pos-Align inserts pivot inside the ring housings, which lets you compensate for small alignment differences between the front and rear rings. That reduces stress on the scope tube and helps you hold a cleaner, more repeatable zero.





Reviews
There are no reviews yet.