Description
Direct thread mounting works fine until you start moving one suppressor between several rifles. That's where this KGM combo earns its keep. The A-TMBA-HUB-C2 pairs KGM's taper mount adapter for HUB (1.375×24) suppressors with a 5/8×24 taper muzzle brake, giving you a fast, repeatable way to attach your can that doesn't depend on how carefully you torqued it that day.
How the A-TMBA-HUB-C2 System Works
The adapter threads into the rear of any HUB-pattern suppressor, whether that's a KGM R30, R30K, R65, R65K, or a HUB can from another maker. The included muzzle brake installs on your rifle's 5/8×24 threads and stays there. When it's time to shoot suppressed, the can threads over the brake and seats against the tapered shoulder, which centers everything on the bore and locks up tight without tools. Recoil keeps it snugged rather than working it loose, and because the taper indexes the same way every time, point of impact shift between mounting sessions stays minimal. Pull the can off and the brake keeps doing its job taming recoil on its own.
Built Like the Rest of the KGM Lineup
KGM machines these components from heat-treated chromoly steel and finishes them with an OXyN gas nitride treatment that shrugs off heat, carbon, and weather. The brake is bored generously enough to pass projectiles up to .338 caliber, so one setup covers everything from a .308 bolt gun to a big magnum hunting rifle with the right threads.
Who Should Grab This Combo
If you own one good HUB suppressor and more than one rifle, this is the practical answer. Pick up extra taper brakes for each barrel and you can move a single can across your whole safe in seconds, with the confidence that it seats concentric and consistent every single time. It's a simple upgrade that makes a shared suppressor feel like it was dedicated to every rifle you own.
Key Specifications
- Manufacturer: KGM Technologies
- Manufacturer Part Number: A-TMBA-HUB-C2
- UPC: 784668807217
- Adapter Thread Pattern: HUB 1.375×24
- Muzzle Brake Thread Pitch: 5/8×24
- Mounting Style: Taper mount, thread-over-brake
- Material: Heat-treated chromoly steel
- Finish: OXyN gas nitride, black
- Bore Diameter: Accepts projectiles up to .338 caliber
- Suppressor Compatibility: KGM R30, R30K, R65, R65K, R6 and other HUB (1.375×24) suppressors
What’s Included
- KGM taper mount adapter for HUB (1.375×24) suppressors
- KGM 5/8×24 taper muzzle brake (A-TMB-S-2)
Frequently Asked Questions
Will the A-TMBA-HUB-C2 work with suppressors from other brands?
Yes, as long as the suppressor uses the industry standard HUB 1.375×24 rear thread. The adapter converts any HUB-pattern can to KGM's taper mount system, so it isn't limited to KGM suppressors. It's a popular route for folks running Dead Air, Otter Creek, and other HUB cans who want a taper interface.
Can I shoot the rifle with just the muzzle brake installed?
Absolutely. The 5/8×24 taper brake is a fully functional muzzle brake on its own, so when the suppressor is on another rifle you still get real recoil reduction. Most people leave a brake permanently mounted on each barrel and just move the can around.
What calibers can I run through this KGM taper mount combo?
The brake is bored to pass projectiles up to .338 caliber, so it handles .30 caliber and 6.5mm rifles with 5/8×24 muzzle threads without issue. Just make sure your suppressor itself is rated for the cartridge you're shooting, since the mount can handle more than some cans are built for.
Does the taper mount hold zero better than direct threading?
That's the whole point of the design. The tapered shoulder centers the suppressor on the bore and seats it identically every time you install it, so point of impact shift between removals stays very consistent. Firing pressure also tends to keep a taper interface snug rather than backing it off the way a plain thread mount can loosen.



Reviews
There are no reviews yet.