Description
The 3/4×24 thread pitch shows up on a lot of big bore barrels, think .450 Bushmaster, .458 SOCOM, and .50 Beowulf builds, and if that describes one of your rifles, the KGM A-DTA-T-3 is the simple fix for getting a HUB suppressor mounted on it. This adapter threads into the rear of any suppressor with the industry standard 1.375×24 HUB pattern and gives you a clean direct thread 3/4×24 interface on the other end. No proprietary mounts, no extra hardware, just spin your can on and go shoot.
Why Titanium Makes Sense on the A-DTA-T-3
KGM machined this adapter from titanium, and that matters more than you might think. Big bore rifles already carry plenty of weight up front, and every ounce you hang off the muzzle changes how the gun balances and swings. Titanium keeps the adapter light without giving up strength, and it shrugs off corrosion better than most steel parts, which is a nice bonus if your rifle lives in a truck or spends wet mornings in a deer stand. The finish is a clean black that blends right in with most suppressor bodies.
Built for KGM Cans and the Whole HUB World
KGM designed this piece for their own R6, R65, R65K, R30, and R30K suppressors, but the beauty of the HUB standard is that it does not stop there. If your can from another maker uses the 1.375×24 rear thread, this adapter will work with it too. That is the whole point of HUB, one mounting ecosystem across dozens of brands, and a quality direct thread adapter like this one is the most affordable and repeatable way to take advantage of it.
Simple Setup, Solid Lockup
Direct thread mounting keeps things dead simple. There are no springs, no ratchet teeth, and no lockup surfaces to wear out, just threads. Torque the adapter into your suppressor, thread the assembly onto your barrel, and check that it stays snug during your first range session as things settle in. For a hunting rig or a precision big bore that stays suppressed most of the time, this is the setup most folks end up preferring.
Key Specifications
- Manufacturer: KGM Technologies
- Manufacturer Part Number: A-DTA-T-3
- UPC: 810042342507
- Barrel Thread Pitch: 3/4×24
- Suppressor Thread Pattern: HUB 1.375×24
- Material: Titanium
- Finish: Black
- Mount Type: Direct Thread
- Compatibility: KGM R6, R65, R65K, R30, R30K and other HUB 1.375×24 suppressors
What’s Included
- KGM A-DTA-T-3 Titanium Direct Thread Adapter
Frequently Asked Questions
Will the KGM A-DTA-T-3 work with suppressors from other brands?
Yes. While KGM built it with their R6, R65, R65K, R30, and R30K cans in mind, it fits any suppressor that uses the industry standard 1.375×24 HUB rear thread. That covers a huge range of modern centerfire suppressors from many manufacturers, so check your can's rear thread spec and you should be set.
What calibers typically use a 3/4×24 thread pitch?
The 3/4×24 pitch is most common on big bore barrels like .450 Bushmaster, .458 SOCOM, and .50 Beowulf. If you have one of those rifles with a factory threaded muzzle, there is a good chance this is the adapter you need. Always confirm your barrel's actual thread spec before ordering, since some big bores use different pitches.
Why choose the titanium version over a steel adapter?
Weight and corrosion resistance are the big wins. Titanium keeps mass off the muzzle, which helps balance on rifles that already wear a heavy can, and it holds up well against moisture and the elements. Strength is not a concern either, since titanium handles the job on rifle-caliber direct thread mounts without issue.
Do I need any special tools to install the A-DTA-T-3?
Nothing exotic. The adapter threads into the rear of your HUB suppressor and then the whole assembly spins onto your 3/4×24 barrel by hand, with a wrench used to snug things to spec. As with any direct thread setup, it is smart to check tightness during your first few range trips until everything settles in.




Reviews
There are no reviews yet.