Description
KGM Technologies builds suppressors for people who take precision seriously, and this taper muzzle brake is the mounting backbone of that system. Spin it onto any rifle with standard 5/8×24 muzzle threads and you have a proper interface for KGM's R30T, R65T, and R338 taper-mount suppressors. The tapered shoulder is the whole point here. Instead of relying on threads alone, the suppressor seats against a machined taper that self-centers and locks up tight every single time. That means consistent alignment, repeatable point of impact, and no can slowly backing itself loose halfway through a range session.
Built From Chromoly, Finished to Last
KGM machines this brake from heat-treated chromoly steel and coats it in an OXyN gas nitride finish. That combination shrugs off heat, muzzle blast, and the general abuse that lives at the business end of a rifle. The bore is opened up to pass projectiles as large as .338, so one brake covers everything from a .308 bolt gun to a 6.5 Creedmoor match rifle to a big .338 magnum, as long as the muzzle wears 5/8×24 threads.
One Brake, Multiple Rifles, One Suppressor
The smart play with taper-mount systems is buying a brake for each rifle you shoot suppressed. Leave the brakes installed and torqued, then move your R30T, R65T, or R338 between guns in seconds. No wrenches at the range, no re-timing anything, and your zero stays predictable because the taper indexes the same way every time. Even without a suppressor attached, the brake ports do real work cutting recoil and keeping the muzzle flat, so it pulls its weight on its own.
If you already run a KGM taper-mount can or you have one working its way through the approval process, this is the piece that makes the whole setup click. Grab one for every host rifle and stop babysitting a direct-thread mount.
Key Specifications
- Manufacturer: KGM Technologies
- Manufacturer Part Number: MA-TMB-S-2
- UPC: 810042350007
- Model: Taper Muzzle Brake
- Product Type: Muzzle Brake / Suppressor Mount
- Thread Pattern: 5/8×24
- Suppressor Compatibility: KGM R30T, R65T, R338
- Bore Diameter: Accepts projectiles up to .338
- Material: Heat-Treated Chromoly Steel
- Finish: OXyN Gas Nitride
- Color: Black
What’s Included
- KGM Taper Muzzle Brake, 5/8×24
Frequently Asked Questions
Which suppressors does this KGM taper muzzle brake work with?
This brake is the mounting interface for KGM's taper-mount line, specifically the R30T, R65T, and R338 suppressors. The suppressor threads over the brake and seats against the tapered shoulder for a self-centering, repeatable lockup. It is not designed for suppressors from other manufacturers or KGM's direct-thread models.
What calibers can I run through the 5/8×24 taper brake?
The bore is opened up to pass projectiles up to .338, so it handles common 5/8×24 chamberings like .308 Win, 6.5 Creedmoor, .300 Win Mag, and the big .338 cartridges. Just match the brake to the suppressor's caliber rating too, since the can is the limiting factor. As long as your muzzle has 5/8×24 threads and enough shoulder, you're set.
Can I use this brake without a suppressor attached?
Yes, it functions as a standard muzzle brake on its own, cutting felt recoil and helping keep the muzzle settled between shots. A lot of folks buy one for each rifle and leave them installed full time. That way the suppressor moves between guns in seconds without any tools.
Will my point of impact shift when I remove and reinstall the suppressor?
That's the main reason taper mounts exist. The tapered shoulder self-centers the suppressor and locks it up the same way every time, so point of impact shifts stay small and predictable compared to loose thread-only mounts. Torque the brake properly at install and the system holds its alignment shot after shot.




Reviews
There are no reviews yet.