0
0

Strike Industries 7-Position Advanced Receiver Extension – Red

UPC: 708747546637

$54.99

18 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

Most folks never give the buffer tube a second thought until they realize their stock is either a touch too long or a touch too short. The Strike Industries Advanced Receiver Extension solves that with seven positions instead of the usual six, which gives you finer control over your length of pull and a better chance at landing that perfect cheek weld. It carries a mil-spec diameter, so it drops onto any standard AR-15 receiver and works with your existing carbine stock.

What sets this tube apart from the extruded mil-spec stuff is the material. It's machined from 7075-T6 aluminum, the same aircraft-grade alloy used in high-stress rifle parts, which gives it noticeably more backbone than the 6061 tubes a lot of makers rely on. Add a hard anodized red finish and you get a part that shrugs off corrosion, bench mishaps, and hard use while looking sharp on the back of your rifle.

Where the Advanced Receiver Extension Earns Its Keep

The scalloped cuts along the body aren't just for looks. They reduce friction and binding when you're sliding a tight-fitting stock on and off, and they trim a little weight without pulling material from the areas that take the most stress. There's also a supported buffer retaining tab built in, which makes indexing the tube during install easier and helps keep the buffer retainer seated the way it should be.

Fitment Notes for the Strike Industries Buffer Tube

This is a carbine-length setup through and through. The internal length matches a standard carbine buffer tube, so it runs your usual carbine buffer and spring with no drama. It is not built for rifle-length buffers or springs, and it won't work with an A5 buffer system, so keep your components carbine-spec. Builders who've run these swear by them, often citing the earlier BCG support and the way the threads protect the lower receiver. If you're chasing the most compact footprint possible, it also pairs up with the Strike Industries Pit Viper stock.

Key Specifications

  • Manufacturer: Strike Industries
  • Manufacturer Part Number: ARARET7RED
  • UPC: 708747546637
  • Product Type: Receiver Extension / Buffer Tube
  • Positions: 7-Position
  • Material: 7075-T6 Aluminum
  • Finish: Red Hard Anodized
  • Length: 7.28 in
  • Tube Diameter: 1.145 in (Mil-Spec)
  • Weight: 3.8 oz
  • Fitment: Standard AR-15 receiver, carbine buffer and spring
  • Stock Compatibility: Strike Industries Pit Viper Stock

What’s Included

  • 1x Strike Industries 7-Position Advanced Receiver Extension (Red)

Frequently Asked Questions

What's the advantage of a 7-position receiver extension over a standard 6-position tube?

The extra position gives you finer adjustment of your length of pull, so you can land on a setting that feels right instead of splitting the difference between two notches. That's handy for dialing in cheek weld and reach across different shooters or gear setups. It still uses a standard carbine stock, so you're not giving anything up to gain that flexibility.

Will this Advanced Receiver Extension work with my existing carbine buffer and spring?

Yes. The internal length matches a standard carbine buffer tube, so your carbine buffer and spring will run in it just fine. Keep in mind it is not made for rifle-length buffers or springs, and it won't work with an A5 buffer system, so stick with carbine-spec components.

Is the 7075-T6 aluminum really stronger than a typical mil-spec tube?

It is. Many standard tubes are made from 6061 aluminum, while this one uses 7075-T6, an aircraft-grade alloy with more strength for its weight. The hard anodized finish also helps it resist corrosion and hold up to bench and field abuse.

Does this tube fit any AR-15 lower and stock?

It's a mil-spec diameter tube, so it threads onto any standard AR-15 receiver and accepts mil-spec collapsible stocks. Builders also like that it supports the bolt carrier earlier and helps protect the lower receiver threads during use. If you want an ultra-compact setup, it pairs with the Strike Industries Pit Viper stock.

Additional information

UPC

708747546637

Manufacturer

Manufacturer Part Number

ARARET7RED

Product Type

Buffer Tube

Reviews

There are no reviews yet.

Be the first to review “Strike Industries 7-Position Advanced Receiver Extension – Red”