Description
Century's USA-made AKs run a slightly different muzzle setup than your typical imported rifle, and that's exactly why Dead Air makes the WV210. This is the M14x1 left-hand long thread insert for the Wolverine PBS-1, built specifically so rifles like the RAS-47, C39, and VSKA can host the suppressor without any fitment headaches. It's an easy fix for a problem that used to leave a lot of Century owners out in the cold.
Why the Wolverine Insert System Works
The whole point of the Wolverine is that one can covers your entire AK collection, and the interchangeable thread inserts are what make that happen. Instead of buying a dedicated suppressor for every thread pitch in the safe, you swap inserts at the rear of the can and move it from rifle to rifle. The WV210 pairs with the standard M14 collar, which is the same one that ships with the Wolverine, so there's nothing extra to buy for most setups. Thread it in, index the suppressor on your muzzle, and you're back in business.
Built to Take AK Abuse
AK-pattern rifles are not gentle on muzzle devices, and Dead Air machined this insert from stainless steel with a black nitride finish to hold up to the heat and carbon that come with the territory. The nitride treatment keeps wear and corrosion in check and gives the insert a low-glare black look that matches the rest of the Wolverine. It's a small part, but it's the piece doing the work of keeping your suppressor aligned and locked down shot after shot.
One Detail Worth Knowing About the WV210
This is the LONG version of the M14x1 LH insert, and that matters. Standard imports like the WASR-10 and Yugo-pattern rifles use the regular-length WV200 insert, while Century's American-made guns need the extra length this one provides. If your rifle rolled out of Century's Georgia factory rather than off a boat, the WV210 is the one you want. Double-check your host before ordering and you'll be set the first time.
Key Specifications
- Manufacturer: Dead Air Silencers
- Manufacturer Part Number: WV210
- UPC: 810128160858
- Model Compatibility: Dead Air Wolverine PBS-1 Suppressor
- Thread Pattern: M14x1 LH (Left-Hand)
- Insert Length: Long
- Host Compatibility: Century USA-made AKs (RAS-47, C39, VSKA)
- Required Collar: M14 Collar (included with the Wolverine suppressor)
- Material: Stainless Steel
- Finish: Black Nitride
- Shipping Weight: 0.145 lbs
What’s Included
- Dead Air Wolverine M14x1 LH Long Thread Insert (WV210)
Frequently Asked Questions
Which rifles does the Dead Air WV210 thread insert fit?
The WV210 is the M14x1 LH long insert made for Century USA-manufactured AK rifles, including the RAS-47, C39, and VSKA. If you're running an imported AK like a WASR-10 or a Yugo OPAP/NPAP, you'll want the standard-length WV200 instead. The two share the same thread pitch but differ in insert length, so match the insert to your specific host.
Do I need to buy a separate collar for this insert?
In most cases, no. The WV210 uses the M14 collar, which is the same collar that ships with the Wolverine suppressor from the factory. Only the larger M24 inserts require a separate collar purchase, so this one should drop right into your existing setup.
How does swapping thread inserts on the Wolverine work?
The inserts thread into the rear of the Wolverine PBS-1 and are held by the appropriate collar, letting one suppressor mount to hosts with different thread pitches. Swapping is a quick job, so you can move the can between rifles in your collection without dedicated mounts on each gun. Just make sure the insert fully seats and the suppressor indexes squarely on the muzzle before shooting.
What is the Wolverine thread insert made of?
It's machined from stainless steel and treated with a black nitride finish. That combination resists heat, carbon fouling, and corrosion, which matters since this part lives right at the muzzle of a hard-running AK. The finish also gives it a low-glare black look that matches the Wolverine itself.




Reviews
There are no reviews yet.