Description
The Talon Armament EV03R takes one of the most common complaints about subcompact Glocks and puts it to rest. Factory polymer frames get slippery when your hands are sweaty, cold, or wet, and on a short-gripped Gen 5 subcompact that little bit of slip matters more than it does on a full-size pistol. This grip is a single piece of textured rubber, cut on a laser to match the frame, that wraps the handle and gives you a positive, non-slip surface right where your hand lives.
What makes the rubber texture the go-to choice is how versatile it is. It grabs well without feeling like sandpaper, so it stays comfortable against bare skin and slides in and out of a holster without chewing up your cover garment. That is exactly why the rubber option is Talon's most popular material by a wide margin, and it is the reason so many concealed carriers reach for it over the more aggressive granulate.
Why the EV03R Fits Your Subcompact Glock Right
This one is cut specifically for the subcompact Gen 5 frame, so you get full coverage on the side panels and backstrap along with the wraps under the trigger guard. The material comes in at less than 0.5mm thick, which means you get all that added grip without changing the profile of the gun or fighting your existing holster.
Getting the EV03R On (and Off)
Install is a job you can knock out at the kitchen table in a few minutes. Field strip the pistol, wipe the frame down with rubbing alcohol so it is squeaky clean, test fit with the backing still on, then peel and press it into place. A hair dryer or heat gun activates the adhesive, and giving it a full cure before heavy handling helps it lock in for the long haul. When you are ready to change it out or sell the gun, it peels off and any leftover residue wipes away with a little rubbing alcohol, leaving the frame just like it was. Talon backs the grip and it is 100% made in the USA.
Key Specifications
- Manufacturer: Talon Armament
- Manufacturer Part Number: EV03R
- UPC: 812308025254
- Material: Rubber
- Texture: Textured Rubber
- Color: Black
- Thickness: Less than 0.5mm
- Attachment: Adhesive backed, wraparound single piece
- Fits: Subcompact Glock Gen 5
- Coverage: Side panels, backstrap, and finger wraps under trigger guard
- Country of Origin: Made in USA
- Removable: Yes, peels off clean
What’s Included
- Talon Armament EV03R adhesive rubber grip (single piece, pre-cut)
- Installation instructions
Frequently Asked Questions
Which Glock models does the EV03R fit?
The EV03R is cut for subcompact Glock Gen 5 pistols, covering the models 26, 27, 28, 33, and 39 in that generation. It is designed for a model-specific fit, so it lines up with the frame cutouts rather than being a one-size sleeve. If your gun is a different generation or frame size, check for the matching Talon part number before ordering.
Will the EV03R add bulk to my carry gun?
No. The rubber material is less than half a millimeter thick, so it adds grip without changing the profile of the frame. That thinness is a big reason it works so well on a subcompact that you are carrying concealed, and it usually plays fine with your existing holster.
Can I remove the grip later without wrecking my frame?
Yes. The adhesive is made to bond to polymer and hold for years, but it peels off cleanly when you want it gone. Any bit of leftover residue wipes right off with rubbing alcohol, returning the frame to its original condition, which is handy if you ever sell the pistol or want to swap textures.
How do I install the EV03R the right way?
Field strip the gun and clean the frame thoroughly with rubbing alcohol, then let it dry completely. Test fit the grip with the backing still on, peel it, press it into place, and warm it with a hair dryer or heat gun to activate the adhesive. Let it cure before any rough handling or range time so the bond sets up strong.





Reviews
There are no reviews yet.