Description
The KRISS Vector is a fun gun straight out of the box, but the stock handguard leaves you short on real estate for accessories. This Strike Industries handguard fixes that in a hurry. It's a one-piece, free-float design that mounts directly to the Vector lower receiver and gives you M-LOK slots to hang whatever your setup calls for, from a weapon light to a vertical grip or hand stop.
What the Strike Vector Handguard Brings to the Table
Strike went with M-LOK rails at the 3, 6, and 9 o'clock positions, so you've got room to spread accessories around without crowding everything onto one plane. The free-float construction means the handguard doesn't touch the barrel, which keeps things clean and adds rigidity up front. It's machined from 6061-T6 aluminum with a black anodized finish, and at right around 4.3 ounces it won't throw off the Vector's balance or turn it into a nose-heavy brick.
Fitment and Suppressor Clearance on the KRISS Vector Handguard
This one is cut for the SDP and SBR models running the 6.5-inch barrel, and it also plays nice with the Vector CRB, the Vector 22 CRB, and Vector square or round barrel shrouds. If you're running a 5.5-inch barrel setup, it'll work as long as your linear comp, can, or muzzle device puts all the ports past the front of the handguard. There's generous internal clearance too, with room for suppressors up to 1.90 inches in diameter, so most cans will tuck inside without drama.
Getting the Strike Handguard Installed
Installation is about as painless as it gets. It's a drop-in job that uses four set screws and the included Torx tool, and Strike even throws in a dab of blue threadlocker so nothing walks loose after a few range trips. No barrel nut, no shims, no gunsmithing. Bolt it on, load it up with your gear, and go run your Vector the way you want it.
Key Specifications
- Manufacturer: Strike Industries
- Manufacturer Part Number: KVHGBK
- UPC: 793811766066
- Model: Strike Handguard for KRISS Vector SDP
- Length: 5.59 in
- Material: 6061-T6 Aluminum
- Finish: Black Anodized
- Weight: 4.26 oz
- Attachment System: M-LOK at 3, 6, and 9 o'clock
- Design: One-Piece Free-Float
- Suppressor Clearance: Up to 1.90 in (48.26mm) diameter
- Installation: Drop-In
- Compatibility: Vector SDP/SBR 6.5in barrel, CRB, 22 CRB, barrel shrouds
What’s Included
- 1x Strike Handguard for KRISS Vector SDP
- 4x Set screws (M4x8mm)
- 1x Torx tool (T20)
- 1x Loctite Threadlocker Blue 243
Frequently Asked Questions
Will this Strike Industries handguard fit my KRISS Vector?
It's designed for the Vector SDP and SBR models with the 6.5-inch barrel, and it also fits the Vector CRB, Vector 22 CRB, and Vector square or round barrel shrouds. If you're running a 5.5-inch barrel, it will work as long as your linear compensator, suppressor, or muzzle device has all its ports past the front of the handguard. Check your barrel length and muzzle setup before ordering to be sure.
How does the KRISS Vector handguard install?
It's a drop-in installation with no gunsmithing required. The handguard mounts directly to the Vector lower receiver using four set screws and the included T20 Torx tool. Strike also includes blue threadlocker to keep the screws from backing out over time.
Can I run a suppressor with this handguard?
Yes. The handguard has internal clearance for suppressors up to 1.90 inches (48.26mm) in diameter, which covers most common pistol-caliber cans. As long as your suppressor fits that dimension, it will tuck inside without rubbing.
Where can I mount accessories on the Strike Vector handguard?
There are M-LOK slots at the 3, 6, and 9 o'clock positions, so you can spread your gear across three planes. That gives you room for a weapon light, laser, vertical grip, hand stop, or M-LOK and SI LINK accessories without stacking everything in one spot.





Reviews
There are no reviews yet.