Description
Piston-driven suppressors like the YHM Sidewinder M2 are built for tilting-barrel pistols, but that recoil booster becomes dead weight the moment you thread onto a fixed barrel. That is exactly the problem this little adapter solves. Pull the spring retainer, spring, and piston out of your Sidewinder, thread the YHM-3250 in their place, and you have a rock-solid direct thread mount for any 5/8-24 muzzle. No tools beyond what you already own, no gunsmith visit, just a quick swap at the bench.
Built Like Everything Else Yankee Hill Makes
The adapter is machined from 17-4 PH stainless steel with a matte black finish, so it shrugs off heat, carbon, and repeated on-and-off cycles without the threads getting sloppy. At three quarters of an inch long and 1.86 ounces, it adds next to nothing to your setup. Like the rest of the YHM lineup, it is made in the USA, and the thread work is clean enough that owners regularly comment on how tight and true the fit is once everything is snugged down.
Where the Sidewinder Carbine Adapter Earns Its Keep
This is the piece that turns one suppressor into a whole-safe solution. Folks run this adapter to put their Sidewinder on 9mm ARs, lever guns, and pistol caliber carbines like the S&W FPC and Ruger PC Carbine, and the 5/8-24 pitch also covers plenty of .30 caliber threaded barrels. It fits the Sidewinder, Sidewinder M2, and legacy Cobra M2 cans, so if you have been holding onto an older YHM suppressor, this keeps it earning its spot.
One Last Note Before You Order
Double check that your muzzle is threaded 5/8-24 before adding this to the cart, since YHM makes this same adapter in several other pitches including 1/2-28 and 1/2-36. And remember the golden rule of direct thread mounting on a fixed barrel: booster assembly out, adapter in. Running both at once is not how this works. Get the right pitch and this is a set-it-and-forget-it upgrade.
Key Specifications
- Manufacturer: Yankee Hill Machine
- Manufacturer Part Number: YHM-3250
- UPC: 816701019421
- Model: Sidewinder Direct Thread Adapter
- Thread Pitch: 5/8-24
- Material: 17-4 PH Stainless Steel
- Finish: Matte Black
- Length: 0.75 in
- Weight: 1.86 oz
- Compatibility: YHM Sidewinder, Sidewinder M2, Cobra M2
- Product Type: Suppressor Mount / Adapter
- Made In: USA
What’s Included
- YHM 5/8-24 Sidewinder Direct Thread Adapter
Frequently Asked Questions
How do I install the YHM Sidewinder carbine adapter?
Remove the spring retainer, spring, and piston from the back of your Sidewinder, then thread this adapter into the suppressor in their place. That converts the can from piston operation to a fixed direct thread mount. It only takes a few minutes and no special tools are required, though a suppressor tool makes retainer removal easier.
Which suppressors does the YHM-3250 adapter fit?
It fits the YHM Sidewinder, Sidewinder M2, and the older Cobra M2 suppressors, since they all share the same rear mount interface. It will not fit HUB-pattern cans or other brands. If you own one of these YHM suppressors, this adapter drops right in.
Can I use this adapter on a fixed-barrel pistol caliber carbine?
Yes, that is exactly what it is made for. Fixed barrels do not cycle a recoil booster properly, so swapping the piston assembly for this direct thread adapter is the correct setup for hosts like a 9mm AR, S&W FPC, or Ruger PC Carbine. Just confirm your barrel is threaded 5/8-24 first.
Do I leave the piston and spring in when using this adapter?
No. The adapter physically replaces the spring retainer, spring, and piston inside the suppressor. Keep those parts in a safe spot, because you will want to reinstall them whenever you move the can back to a tilting-barrel pistol.





Reviews
There are no reviews yet.