$150.00
53 in stock
Online inventory may differ from in-store availability.
Quick turnaround so you get your gear sooner.
Trusted checkout with industry-standard protection.
Keeping Traditions Alive Since 1953
Secure Transactions provided with 
There are plenty of quick-attach suppressor systems out there, but most of them buy speed with extra parts. Springs, latches, shims, ratchet teeth, all of it adds weight and more things that can wear out. Q went a different route with the Plan-B Omega. It threads into your Omega-pattern suppressor and mates to a Q Cherry Bomb muzzle brake using matched precision tapers. That taper-on-taper fit gives you a huge amount of contact surface, so the can snugs down hard, self-centers on the bore, and returns to the same spot every time you spin it on. No timing the muzzle device, no crush washers, no gimmicks.
If you have been running a big ratchet-style mount on the back of your can, swapping to the Plan-B is one of the easiest weight cuts you can make. The mount itself weighs right around 1.85 ounces of heat treated 17-4 stainless steel, which is a serious drop from most factory QD hardware. Less mass hanging off the muzzle means better balance, less barrel whip, and a rifle that just points nicer. The copper-colored finish looks sharp too, though shade can vary a bit piece to piece, which is part of the character.
This version fits Omega-pattern suppressors, and the list is longer than you might think. SilencerCo Omega 300, Harvester Big Bore 338, and Hybrid, plus the Dead Air Nomad, Energetic Armament VOX, YHM Turbo K, and Banish 338 all take this mount. Threading is 1.375×24, and it is set up for .30 caliber applications. You will need a Cherry Bomb brake on the host rifle, sold separately, but once that is on, moving one can between multiple rifles takes seconds.
One underrated perk of the taper system is thread protection. The sealed taper interface keeps carbon from baking onto your muzzle threads, so the can comes off clean even after long range sessions instead of feeling welded on. Simple, strong, and repeatable is a tough combination to argue with.
It is built for Omega-pattern cans, which covers the SilencerCo Omega 300, Harvester Big Bore 338, and Hybrid, along with the Dead Air Nomad, Energetic Armament VOX, YHM Turbo K, and Banish 338. If your suppressor uses the same rear mount pattern as the Omega 300, odds are good it will work. When in doubt, check with your suppressor's manufacturer before ordering.
Yes, the Plan-B Omega is one half of a two-piece system. The mount threads into your suppressor while a Q Cherry Bomb brake lives on the rifle, and the two mate together with matched tapers. The Cherry Bomb is sold separately, so pick the brake that matches your barrel's thread pitch.
In most cases you can use the same spanner or mount tools that came with your suppressor to remove the factory mount and thread in the Plan-B. For example, the wrenches included with a Dead Air Nomad handle the swap without any extra purchases. It is a quick job you can do at the bench in a few minutes.
That is the whole point of the design. The taper-on-taper interface self-centers the suppressor on the bore and creates a large contact surface, so lock-up is consistent shot after shot and swap after swap. There are no springs, latches, or ratchet teeth to wear out and introduce play over time.
| UPC | 860248000459 |
|---|---|
| Manufacturer | |
| Manufacturer Part Number | PLAN-B-OMEGA |
| Caliber/Gauge | .30 Carbine |
| Color | COPPER |
| Length | 5 |
| Model | |
| Package Height | 1.0 |
| Package Width | 3.6 |
| Product Type | Accessory-Muzzle Brakes |
| Shipping Weight | 0.15 |
| Thread Pattern | 1.375"x24 |
You must be logged in to post a review.
Reviews
There are no reviews yet.