Description
Yankee Hill Machine has been running the Phantom QD system since 2005, and there is a reason it has stuck around this long: it just works. This 1/2-28 threaded mount gives you a genuine five port flash hider when your can is off the gun, and a fast, repeatable attachment point when it is on. Thread it onto the muzzle, spin your suppressor down over it by hand, and the external locking mechanism snaps it into place with clear feedback so you know it is seated. No wrenches at the range, no guessing.
What Makes the Phantom LT/LTA QD Mount Work
YHM updated this design with a few smart touches. Carbon scraper teeth on the mount clean fouling out of your suppressor's internal support surfaces every time you attach it, which matters more than people think after a few hundred rounds. A dual support system aligns the can with your bore for consistent point of impact, and the external lock keeps heat away from the high temperature spring so it holds up over a long service life. The whole thing is steel with a black finish that shrugs off corrosion and hard use.
Suppressor Compatibility for the YHM 4302-28A
This is the 4302 series mount, which covers a lot of ground. It runs YHM's legacy .30 caliber cans including the Phantom .30, Phantom LT/LTA, and first generation Nitro and Resonator suppressors. It also works with any 1.375×24 HUB capable suppressor wearing YHM's Phantom QD Adapter (YHM-3060), which brings the Fat Cat, Turbo T2, Turbo T3, Turbo K, Turbo K-RB, Resonator R2, Resonator RK, and Nitro N2O into the mix. It will not fit the Phantom 5.56, Phantom 5.56 M2, or generation 1 Turbo cans, so double check what you are running before you order.
Mounting the Phantom QD Flash Hider
Installation is straightforward on any 1/2-28 muzzle. YHM calls for 20 to 30 foot pounds of torque and specifically says to skip crush and peel washers, so use shims if you need to time it. Grab one for each host rifle and you can float a single suppressor across your whole safe.
Key Specifications
- Manufacturer: Yankee Hill Machine
- Manufacturer Part Number: YHM-4302-28A
- UPC: 816701017007
- Model: Phantom LT/LTA 7.62 Q.D. Flash Hider
- Type: Quick-detach flash hider / suppressor mount
- Thread Pattern: 1/2"-28 tpi
- Caliber: .308 / 7.62 NATO (.30 Cal)
- Material: Steel
- Finish: Black Melonite
- Port Design: 5-port flash suppression
- Weight: 4.1 oz
- Recommended Torque: 20-30 ft-lbs (no crush or peel washers)
- Suppressor Compatibility: YHM Phantom .30, Phantom LT/LTA, gen 1 Nitro/Resonator, and 1.375×24 HUB cans with YHM-3060 adapter
What’s Included
- YHM Phantom LT/LTA QD flash hider mount
Frequently Asked Questions
Which suppressors work with the YHM Phantom LT/LTA QD mount?
This 4302 series mount fits YHM's legacy .30 caliber cans like the Phantom .30, Phantom LT/LTA, and gen 1 Nitro and Resonator. It also pairs with any 1.375×24 HUB suppressor running YHM's Phantom QD Adapter (YHM-3060), including the Fat Cat, Turbo T2/T3, Turbo K and K-RB, Resonator R2 and RK, and Nitro N2O. It will not work with the Phantom 5.56, Phantom 5.56 M2, or gen 1 Turbo.
Does this mount still reduce flash without a suppressor attached?
Yes, that is half the point of the design. The five port layout carries over the flash hiding performance of the original Phantom, so your rifle runs a capable flash hider full time. When you want the can on, it doubles as the quick-detach interface.
How do I install the Phantom QD mount and does it need timing?
It threads onto any 1/2-28 muzzle and YHM recommends torquing to 20 to 30 foot pounds. Do not use crush or peel washers, since those can throw off suppressor alignment. If the ports need clocking, use a shim kit to time it properly.
Will the 1/2-28 thread work on my .30 caliber barrel?
This version is made for hosts with 1/2-28 muzzle threads, which shows up on some .30 caliber and smaller bore rifles. Most .308 and 6.5 barrels run 5/8-24 threads, and YHM offers this same mount in that pitch as the YHM-4302-24A. Check your barrel's thread pitch before ordering to get the right one.






Reviews
There are no reviews yet.