Description
Rebarreling a Savage is one of the easier projects a home builder can tackle, and this wrench is the piece that makes it possible. The Wheeler Savage Barrel Nut Wrench is a double-ended tool made to turn the barrel nut on and off a Model 10 or 110 receiver, which is how you pull a factory tube and install a fresh barrel without a lathe. One end is notched for the older round-bottom nuts and the other handles the newer square-bottom style, so it covers early and late guns from the same box. A brass shim comes along to help it sit right on different nut profiles, and it fits the smooth nuts too.
What the Savage Barrel Nut Wrench Handles
The wrench is cut from 3/16-inch steel and runs on a long, roughly one-inch steel handle, which is exactly what you want when a factory nut has been torqued down and locked in place for years. That leverage is the difference between backing a nut off cleanly and rounding it out with the wrong tool. It also works on Model 12 rifles, which share the same barrel nut system, so it covers more of the Savage bolt-gun lineup than the name suggests.
Torque and Headspace Control with the Savage 10/110 Wrench
Two 1/2-inch square drive holes let you run it with a swing bar for muscle or a torque wrench when you want repeatable numbers. That torque fitting matters because the whole appeal of a Savage barrel swap is setting your own headspace. With the ejector out of the bolt and a GO gauge in the chamber, you thread the barrel in until it bumps the gauge, then snug the nut and torque it down, typically in the 80 to 90 ft-lb range, and check the bolt closes on GO but not on a NO-GO. It is a straightforward process once you have the right wrench in hand.
Pair it with a barrel vise and a set of headspace gauges and you have the core kit for building or rechambering a Savage at the bench. This is a well-made tool that earns its spot in a builder's drawer.
Key Specifications
- Manufacturer: Wheeler Engineering
- Model: Savage Barrel Nut Wrench
- Manufacturer Part Number: 123038
- UPC: 661120230380
- Product Type: Action / Barrel Nut Wrench
- Fit: Savage 10 and 110 Series (also fits Model 12)
- Nut Compatibility: Early round-bottom and late square-bottom nuts, plus smooth nut
- Drive: Two 1/2 inch square drive holes
- Material: 3/16 inch steel
- Color: Black
- Length: 12.7 in
- Country of Origin: Made in the USA
- Warranty: Limited lifetime warranty from Wheeler
What’s Included
- Notched barrel nut wrench
- Smooth barrel nut wrench
- Brass shim
Frequently Asked Questions
Does the Savage barrel nut wrench fit both old and new barrel nuts?
Yes. It is double-ended, with a notched end for the older round-bottom nuts and a smooth end for the newer square-bottom nuts. A brass shim is included to help it seat correctly on different nut profiles, so you are covered on both early and late model Savage rifles.
Will this wrench work on rifles other than the Savage 10 and 110?
It is built for the Savage 10 and 110 series, and it also fits the Model 12 since those rifles use the same barrel nut setup. If your Savage bolt gun uses the standard barrel nut system, this wrench should turn it.
Can I use a torque wrench with the Savage barrel nut wrench?
You can. It has two 1/2-inch square drive holes, so you can run a swing bar for breaking loose a stubborn nut or a torque wrench when you want a repeatable, measured number. Most Savage builds get the barrel nut torqued in the 80 to 90 ft-lb range.
What else do I need to swap a barrel on my Savage?
Along with this wrench you will typically want a barrel vise to hold the barrel steady and a GO gauge (a NO-GO is handy for verification) to set headspace. With the ejector removed from the bolt, you thread the barrel in until it contacts the GO gauge, then tighten and torque the nut. That is what makes a Savage one of the friendlier rifles to rebarrel at home.




Reviews
There are no reviews yet.