Description
Quick-detach suppressor mounts have a reputation for being heavy, bulky, and fussy. Yankee Hill Machine went the other direction with the sRx line, and this Long Q.D. Flash Hider is a good example of why the system has caught on. It threads onto a 5/8-24 muzzle, pairs with the sRx adapter (YHM-4400, sold separately) on any industry-standard 1-3/8×24 HUB suppressor, and gives you a hand-tight, tool-free mount that adds barely any length or weight to the stack.
How the sRx Flash Hider Locks Up
The magic is in the large internal taper machined ahead of the mounting threads. When you spin your can on, that taper does the actual locking and sealing, so gas and carbon never reach the threads themselves. That means no baked-on fouling to fight when it is time to pull the suppressor, and consistent, repeatable lockup every time you remount. There are no springs, latches, or moving parts to wear out or rattle loose, and the design does not require timing or shim kits during install. Thread it on, torque it down, and you are done.
Built Like You Would Expect From Yankee Hill
This is machined steel with a black phosphate finish, made in the USA by a company that has been building suppressors and muzzle devices for decades. The long birdcage-style body handles flash reduction duty on its own when the can is off, so your rifle is not stuck wearing a bare mount between range trips. It runs about 2.3 inches overall and is rated for 9mm and smaller bores, which covers .308 and 7.62 NATO barrels wearing 5/8-24 threads.
Where the sRx Long Q.D. Fits in Your Setup
If you already run a YHM Fat Cat, Turbo, Resonator, or any other HUB-pattern suppressor, this flash hider plus the sRx adapter is one of the lighter and slimmer quick-detach routes on the market. It is a smart pick for anyone splitting one can across multiple rifles, since extra flash hiders are far cheaper than extra suppressors. Just remember the sRx adapter is required and sold separately.
Key Specifications
- Manufacturer: Yankee Hill Machine
- Manufacturer Part Number: YHM-4405-24
- UPC: 841812101550
- Model: sRx Long Q.D. Flash Hider
- Muzzle Thread Pitch: 5/8"-24 tpi
- Suppressor Interface: HUB 1-3/8"x24 (via sRx adapter, sold separately)
- Caliber Rating: 9mm and smaller (covers .308 / 7.62 NATO)
- Overall Length: 2.30 in
- Material: Steel
- Finish: Black phosphate
- Mounting Style: Taper seal quick-detach, no timing or shims required
- Country of Origin: Made in USA
What’s Included
- Yankee Hill sRx Long Q.D. Flash Hider, 5/8-24 (sRx adapter YHM-4400 sold separately)
Frequently Asked Questions
Does the sRx Long Q.D. Flash Hider work with non-YHM suppressors?
Yes, as long as your suppressor accepts the industry-standard 1-3/8×24 HUB thread pattern. You will need the YHM sRx adapter (YHM-4400) installed in the suppressor, and once that is in place the flash hider will lock up with any HUB-compatible can, YHM or otherwise.
Is the sRx adapter included with this flash hider?
No, the flash hider ships by itself. The sRx adapter (YHM-4400) threads into your HUB suppressor and is sold separately. Once you own one adapter, you only need additional flash hiders to move a single suppressor between multiple rifles.
Will this 5/8-24 sRx flash hider work on my .308 rifle?
Yes. The Long version of the sRx flash hider is rated for 9mm and smaller bores, which comfortably covers .308 and 7.62 NATO. The 5/8-24 thread pitch is the standard for most .308 pattern rifles, so it should thread right onto your barrel.
Do I need to time or shim the sRx flash hider during installation?
No. The sRx design does not require timing to the barrel, so there are no shim kits or crush washers to mess with. The internal taper ahead of the threads handles alignment and sealing, which also keeps carbon and gas off the mounting threads for easy suppressor removal.






Reviews
There are no reviews yet.