0
0

YHM sRx Long Q.D. Muzzle Brake 5/8-24 for HUB Suppressors, Phosphate

UPC: 841812101536

$84.75

3 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

Quick-detach mounts have a habit of adding bulk, weight, and a pile of little parts that wear out. Yankee Hill Machine took a different route with the sRx system, and this Long sRx Q.D. Muzzle Brake is the barrel-side half of it. Threaded 5/8-24 for .308 and 7.62 NATO rifles, it screws on without any shimming or timing, then works hand in hand with the sRx Adapter (YHM-4400) to give you a genuinely simple suppressor mount with zero moving parts.

How the sRx Long Brake Seals Up

The trick is the large internal taper machined in front of the threads. When your adapter-equipped suppressor spins on, that taper does the locking and sealing, so hot gas and carbon never reach the threads themselves. That means no baked-on fouling, no stuck cans after a long range day, and consistent lockup every single time you mount up. Since the adapter runs the industry standard 1.375×24 HUB thread, this brake plays nice with YHM's Fat Cat and Cat's Ass suppressors along with the wide world of HUB-compatible cans.

Built Light, Runs Unsuppressed Too

At roughly 2.3 inches long and just under two ounces, the sRx Long brake adds very little to the end of your barrel, and it comes in lighter than a lot of QD mounts on the market. Shooting without the can? The brake ports go to work taming recoil and muzzle rise like any solid .30 caliber brake should. The black phosphate finish shrugs off corrosion and matches most working rifles without drawing attention to itself.

Why Run the YHM sRx Muzzle Brake

YHM builds their gear in Massachusetts and backs it with a lifetime warranty, and the sRx line reflects decades of suppressor mount experience distilled into something refreshingly simple. If you want a clean-looking rifle that takes a suppressor on and off in seconds without babysitting threads, this is a smart way to set it up. Just remember it needs the sRx Adapter on your can to complete the system.

Key Specifications

  • Manufacturer: Yankee Hill Machine
  • Model: sRx Long Q.D. Muzzle Brake
  • Manufacturer Part Number: YHM-4405-MB-24
  • UPC: 841812101536
  • Thread Pattern: 5/8"-24 TPI
  • Caliber Compatibility: .308 / 7.62 NATO
  • Device Length: 2.3 in
  • Length Added to Barrel: Approx. 1.675 in (with 0.6 in barrel threads)
  • Weight: 1.92 oz
  • Finish: Black Phosphate
  • Mount Compatibility: YHM sRx Adapter (YHM-4400), 1.375×24 HUB standard
  • Installation: No shimming or timing required
  • Warranty: YHM Lifetime Manufacturer's Warranty

What’s Included

  • YHM sRx Long Q.D. Muzzle Brake, 5/8-24

Frequently Asked Questions

Do I need anything else to use the YHM sRx Long Muzzle Brake with my suppressor?

Yes, this brake is one half of a two-piece system. Your suppressor needs the YHM sRx Adapter (YHM-4400), which threads onto any can with the standard 1.375×24 HUB interface. Once the adapter is on your suppressor, it locks onto this brake using the internal taper for a fast, repeatable mount.

Does the sRx Long Q.D. Muzzle Brake require timing or shims to install?

No, and that is one of the best parts of the sRx design. There is no clocking or shimming required, so installation is as simple as threading it onto your 5/8-24 muzzle and torquing it down. The taper handles alignment and lockup with the adapter, not the position of the ports.

Will this work with suppressors from other brands, or only YHM cans?

It works with more than just YHM. Since the sRx Adapter uses the industry standard 1.375×24 HUB thread, any HUB-compatible suppressor can run on this mount once the adapter is installed. It is a natural fit for YHM's Fat Cat and Cat's Ass suppressors, but you are not locked into one brand.

How does the taper seal help compared to a regular thread-on mount?

The large taper sits in front of the threads, so when the suppressor locks on, hot gas and carbon are sealed away from the threaded surfaces. That prevents the baked-on fouling that makes direct-thread cans hard to remove after a long shooting session. You get consistent lockup and easy removal even after heavy use.

Additional information

UPC

841812101536

Manufacturer

Manufacturer Part Number

YHM-4405-MB-24

Caliber/Gauge

.308 / 7.62 NATO

Color

Black

Length

7.1

Model

Package Height

1.4

Package Width

3.2

Product Type

Accessory-Muzzle Brakes

Shipping Weight

0.15

Thread Pattern

5/8"-24 tpi

Reviews

There are no reviews yet.

Be the first to review “YHM sRx Long Q.D. Muzzle Brake 5/8-24 for HUB Suppressors, Phosphate”