Description
The Magpul Hunter 700L takes one of the most trusted rifle actions ever made and wraps it in a stock built for real fieldwork and range time. It is a genuine drop-in upgrade for standard Remington 700 pattern long actions running the factory hinged floorplate, so you get modern ergonomics and adjustability without paying custom chassis money. The reinforced polymer shell rides on a Type III hard anodized A380 cast aluminum V-bedding block, which is the piece that keeps your action seated the same way every time and lets you skip traditional bedding work.
What the Hunter 700L Brings to Your Rifle
Adjustability is where this stock earns its keep. The length of pull runs roughly 13 to 15 inches using the included spacer system, so it fits everyone from smaller-framed folks to a big shooter layered up in winter gear. It ships with a 0.25-inch cheek riser and accepts optional 0.00, 0.50, and 0.75-inch risers to get your eye lined up behind glass. The 60-degree grip angle pulls your hand into a more vertical, controlled position, and the soft rubber recoil pad soaks up the thump from magnum long-action calibers like .30-06 and .300 Win Mag.
Free-Floating and M-LOK Ready
The tapered beam design adds rigidity and fully free-floats compatible barrels, accepting all factory Remington profiles plus aftermarket barrels up to 0.920 inches in diameter measured 5.50 inches forward of the breech. M-LOK slots run along the sides and bottom of the forend, so bipods, sling hardware, and rails bolt right on. There are also dimpled drill points for traditional swivel studs and rear QD compatibility with the right kit.
Room to Grow With the 700L
One of the smartest things about this stock is the upgrade path. Drop in Magpul's Bolt Action Magazine Well 700L down the road and you can run detachable AICS-spec box magazines in .30-06 or .300 WM pattern, no gunsmith or custom inletting needed. It fits right-hand receivers and is proudly made in the USA.
Key Specifications
- Manufacturer: Magpul Industries
- Manufacturer Part Number: MAG483-ODG
- UPC: 840815109815
- Model: Hunter 700L
- Color: O.D. Green
- Fits: Remington 700 Long Action (right-hand)
- Action Type: Bolt Action
- Material: Reinforced polymer with A380 cast aluminum V-bedding block
- Length of Pull: Approx. 13.0 to 15.0 in (spacer adjustable)
- Comb Height: 0.25 in riser included, optional risers available
- Grip Angle: 60 degrees
- Barrel Clearance: Free-floats up to 0.920 in diameter, 5.50 in forward of breech
- Accessory Mounting: M-LOK slots on forend sides and bottom
- Weight: Approx. 3.2 lbs (without action and bottom metal)
- Country of Origin: Made in USA
What’s Included
- Magpul Hunter 700L stock (OD Green)
- 0.25-inch cheek riser (installed)
- Length of pull spacers
- Rubber recoil butt-pad
- Installation instructions
Frequently Asked Questions
Is the Magpul Hunter 700L a true drop-in fit for my Remington 700?
For standard Remington 700 pattern long actions with the factory hinged floorplate, it is designed to drop right in with no bedding required. That said, factory action screws vary in length, so some rifles need the screws ground to length or replaced to seat everything perfectly. Plan on a screwdriver, a torque wrench, and a few minutes rather than a gunsmith visit.
Will the Hunter 700L work with a J-Lock bolt shroud?
Rifles equipped with the older J-Lock bolt and shroud can have clearance issues where the extended cocking piece contacts the cheek piece when the bolt is fully retracted. The common fixes are swapping to a standard firing pin assembly or running a no-rise cheek riser. If your 700 has a standard shroud you are good to go.
Can I run a detachable magazine with the Hunter 700L?
Yes, but not out of the box. The stock is set up to accept Magpul's Bolt Action Magazine Well 700L, which lets you feed from AICS-spec box magazines in .30-06 or .300 Win Mag pattern with no custom inletting. Add it whenever you are ready to convert from the floorplate.
What barrel contours will free-float in this stock?
The Hunter 700L accepts all factory Remington barrels and clears aftermarket profiles up to 0.920 inches in diameter measured 5.50 inches forward of the breech, which covers everything up to a Medium Palma contour. The tapered beam keeps the barrel channel open so nothing touches the tube. That is what gives you the consistent, repeatable accuracy people upgrade for.







Reviews
There are no reviews yet.