$79.90
165 in stock
Online inventory may differ from in-store availability.
Quick turnaround so you get your gear sooner.
Trusted checkout with industry-standard protection.
Keeping Traditions Alive Since 1953
Secure Transactions provided with 
The Anchor Brake on the front of your SilencerCo can does its job, but it adds length and it is not doing your ears any favors when you are shooting smaller bores. The Bravo Front Cap AC1341 is the fix. It is a flat front cap machined from 17-4 stainless steel with a bore sized for .224 caliber and 5.56 NATO, and it threads right into the Bravo interface where the Anchor Brake used to live. On an Omega 300 running a direct thread mount, that swap takes the suppressor from 7.09 inches down to about 6.06 inches. An inch may not sound like much on paper, but on a carbine you carry all day, you will notice it.
Here is the part a lot of folks miss. A .30 caliber suppressor shooting 5.56 leaves a lot of extra room around the bullet at the muzzle, and that gap lets sound escape. Matching the front cap opening to the caliber you are running tightens things up, and SilencerCo says running the correctly sized cap can knock down sound levels by roughly 2 to 5 decibels depending on the setup. That is a real, hearable difference, and it costs you nothing in weight or bulk. Just remember this cap is sized for 5.56, so swap back to a larger bore cap before sending .30 caliber rounds through.
The Bravo interface is shared across a chunk of the SilencerCo lineup, so this cap works with the Omega 300, Hybrid 46, Scythe-Ti, and any other suppressor built around the Bravo front cap system. The Sniper Gray finish matches the factory look on gray Omega-series cans, and the 17-4 stainless construction shrugs off heat and blast the same way the rest of the suppressor does.
If you shoot mostly 5.56 through a Bravo-compatible can, this is one of those small upgrades that earns its keep every single range trip. Shorter, quieter, and it takes about a minute to install.
It fits any SilencerCo suppressor built on the Bravo front cap interface, which includes the Omega 300, Hybrid 46, and Scythe-Ti. It threads into the front of the can in place of the standard Anchor Brake. If your can uses the Bravo system, this cap will drop right in.
No, this version has a bore sized for .224 caliber projectiles, so it is strictly for 5.56 and similar diameter rounds. Sending a .30 caliber bullet through it would cause a strike. SilencerCo makes a 7.62 version of the Bravo cap (AC1340) if you need to run larger calibers.
Yes, matching the front cap bore to your caliber tightens up the exit opening and reduces sound escaping around the bullet. SilencerCo puts the improvement in the range of roughly 2 to 5 decibels depending on the host and load. You also drop about an inch of overall length compared to the Anchor Brake.
On an Omega 300 with a direct thread mount, replacing the Anchor Brake with this flat cap takes the suppressor from 7.09 inches down to 6.06 inches. That is right around an inch of savings, which makes a noticeable difference in handling on shorter rifles and pistols.
| UPC | 817272015232 |
|---|---|
| Manufacturer | |
| Manufacturer Part Number | AC1341 |
| Caliber/Gauge | .223 REM/5.56 NATO |
| Color | Sniper Gray |
| Length | Bravo Front Cap |
| Model | |
| Package Height | 0.5 |
| Package Width | 4.2 |
| Product Type | Front End Cap |
| Shipping Weight | 0.095 |
| Sights | 17-4 Stainless Steel |
You must be logged in to post a review.
Reviews
There are no reviews yet.